About me

I’m Ahmad, a mechanical engineering student at Carleton University. I enjoy taking a design from its first calculations through CAD, simulation, and fabrication.

At Raven’s Racing, I work on drivetrain, powertrain, and aerodynamics for Formula SAE. My recent projects include the RR27’s adjustable drivetrain and final drive selection. As a research assistant at Carleton, I design test hardware for high temperatures and pressure loads in vacuum and use lab data to check the models.

Raven’s Racing car and team members at the University of Toronto Shootout
Raven’s Racing took first place at the University of Toronto Shootout.
Ahmad and teammates working at a flow bench
Testing an intake restrictor on the flow bench.

Outside engineering

I spend my free time with family and friends, in the gym, or playing soccer, basketball, and tennis. I follow UFC and cheer for Real Madrid. I also love travel, wildlife, and camping. My curiosity about engineering takes me from robotics and semiconductors to HVAC. I like figuring out how things work and how they could work better.

Ahmad attempting a backflip off a boat in Cancún
my first (and only) attempt at a backflip in Cancun
Ahmad standing in front of the pyramid at Chichén Itzá
chichen itza (a seven wonder of the world)
Ahmad standing outdoors near a buck
me next to a very angry buck
Juvenile red-tailed hawk perched outdoors
juvenile red tailed hawk
Stars over the horizon during a camping trip
nightview when me and my friends went camping

Projects

All projects

Tesla Roadster Stunt Dynamics

MAAE 2101 Engineering Dynamics · Carleton University

Rear view of the Tesla Roadster at the foot of the curved test ramp

How much force does a car need to reach 60 mph in under a second, stay on a ramp past vertical, and roll through 360° in mid-air? Our team used planar rigid-body dynamics to estimate the forces, moments, and energy behind three Roadster demonstrations.

We estimated the car’s centre of gravity and inertia with a composite-body model. We used free-body diagrams, impulse–momentum, and work–energy to derive and cross-check the results, then compared the model with measurements from the demonstration footage.

Three video stills showing the Roadster launching, climbing the inverted ramp, and rolling above a line of vehicles
The three manoeuvres studied. Stills from the Tesla demonstration footage cited in the report.

Thrust-assisted launch

The tyres-only model took about 3.1 seconds to reach 60 mph. Tesla’s reported 0.81-second run implies an average of about 3.4 g and 61.3 kN of net force for the estimated 1,850 kg mass. Frame tracking suggested acceleration built during the run, although the report could not confirm that the overhead clip played in real time.

Bar chart comparing four modelled 0 to 60 mph times with the reported 1.00 and 0.81 second runs
Modelled 0–60 mph times with different sources of traction and thrust, compared with the reported runs.

Inverted ramp and release

The suction requirement peaked at 1.27 times the car’s weight at 131°, while the rear tyres still needed traction and gravity was already pulling the car away from the ramp. After release, the car’s initial spin supplied about 60° of the 190° needed to land wheels down. The model estimated a pitch moment of about 29 kN·m to complete the rotation.

Required suction versus ramp angle, with a peak of 1.27 times vehicle weight at 131 degrees
Estimated suction requirement along the ramp at 5 m/s with an assumed tyre friction coefficient of 1.2.
Plots showing centre-of-gravity height and pitch angle over time after the Roadster leaves the ramp
Predicted height and pitch angle from ramp release to landing.

Kickflip

The model put the peak height at about 9 m. Rolling through 360° accounted for about 6% of the jump’s energy, with most of that energy going into gaining height. The modelled flight heights matched the tracked video measurements to within about 0.2 m.

Modelled kickflip height and roll angle plotted against measurements tracked from the video
Kickflip height and roll angle over time, comparing the analytical model with tracked video.

The report treats the results as engineering estimates, with typical uncertainty of about ±15% due to estimated mass properties, tyre grip, and video scale.

Team: Ahmad Bitar, Abdalla Ubaid, Dalu Obiakor, and Mohamad Chahrour.

All projects

RR27 Drivetrain

Formula SAE · CAD · FEA · CNC Manufacturing

CAD render of the RR27 differential and optimized mounting plates

The RR27 needed a lighter drivetrain mount that kept the sprockets aligned and made the chain easier to tension. I designed a pair of topology-optimized 6061 aluminum plates and an eccentric bearing disc that shifts the differential axis as it rotates.

Design and analysis

  • The eccentric disc provides 0.7 in of travel between the two adjustment extremes.
  • I used static load calculations, FEA and buckling analysis to guide the design. The updated portfolio reports a factor of safety of at least 2 and a buckling load factor of at least 10.
  • The optimized frame is more than 75% lighter than the starting design. I selected the limited-slip differential, 520-series sprockets and chain, and prepared engineering drawings for the manufacturing team.

Status

The design has been handed off for manufacturing. Team feedback and reliability testing will inform the next revision.

Eccentric bearing disc with an off-centre bore
CAD model of the eccentric bearing disc for chain tension adjustment.
Colour contour and legend for von Mises stress on two optimized plates
Von Mises stress plot for both topology-optimized RR27 mounting plates.
Original drivetrain mounting plate with solid web
Baseline mounting plate before topology optimization.
Optimized mounting plate with cutouts
RR27 mounting plate after topology optimization, with cutouts to reduce mass.
Earlier mounting design
Interactive 3D model of the earlier drivetrain mount
All projects
Illustration of a three-axis warehouse robot arm

Warehouse Robot Arm

Python · Robotics · Machine Learning

The question

I modelled a three-degree-of-freedom arm for automated warehouse positioning. The challenge was to calculate joint movements quickly while still reaching the requested positions accurately. I tested whether a learned inverse-kinematics solver could improve calculation speed.

What I did

  • Developed a 3-DOF robotic arm model using forward and inverse kinematics, Jacobian matrices and Cartesian trajectory planning.
  • Trained a three-layer multilayer perceptron on 50,000 simulated joint configurations to predict inverse-kinematics solutions.
  • Compared the MLP's joint-angle predictions with a numerical inverse-kinematics solver, then used PID joint control to follow the commanded angles.

How the control system worked

Cartesian trajectory planning provided target positions for the arm. The three-layer MLP took each target position and predicted the joint angles needed to reach it; a numerical inverse-kinematics solver provided the comparison path. In either case, the resulting angles became setpoints for the PID joint controllers, which used joint-position feedback to drive the arm toward those setpoints. The MLP solved the positioning calculation; PID controlled the motion that followed.

What it found

  • The learned model achieved a mean positioning error of 2.1 mm.
  • Inverse-kinematics computation time fell by 68%, from 8.4 ms to 2.7 ms.
  • Target-reach success remained at 98.5%.

Why it mattered

I demonstrated a faster way to calculate arm positions while retaining high target-reach success. Separating the inverse-kinematics solver from joint control let me compare the MLP with the numerical method under the same PID control approach.

Cartesian target positions feed either a three-layer MLP or a numerical inverse-kinematics solver; both produce joint-angle setpoints for PID controllers, which drive the 3-DOF arm using joint feedback
Robot control workflow · MLP and numerical solver compared at the inverse-kinematics stage; PID follows either set of joint-angle commands
Bar chart comparing 8.4 millisecond numerical inverse kinematics with 2.7 millisecond learned inverse kinematics
Solver computation time in the simulated benchmark.
All projects

Cycloidal Gearbox

SOLIDWORKS · MATLAB · Mechanical Design

Assembled cycloidal gearbox with stepper motor

I designed a compact 25:1 two-disc cycloidal reducer for the highest-load joint on a 0.6 m, six-axis robot arm. I estimated 16 N·m working torque and 25 N·m peak torque from the arm’s mass model, then selected a NEMA 23 closed-loop stepper, a power-off brake, and 608 and 61805 bearings.

Design and verification

I generated the cycloidal disc profile in MATLAB and checked undercut, contact stress, and pin clearance over a full revolution. The minimum calculated pin clearance was 15 µm. The discs are offset by 180° to balance eccentric loads. The design uses 26 ring pins and eight output pins.

The 49-part CAD assembly passed the interference check. The next step is to build the 6061 aluminum and PETG prototype and measure backlash, torque capacity, and efficiency.

Exploded CAD drawing of the gearbox and feedback motor
Exploded assembly showing the two discs and output pins.
All projects

Reactor Gasket Thermal Analysis

Fusion 360 · ANSYS Mechanical · Thermal Analysis

Interactive 3D model of the FFC reactor

Drag to rotate. Shift + drag or drag with two fingers to pan. Scroll or pinch to zoom.

The molten-salt FFC reactor is designed to hold calcium chloride at 950 °C during a 24-hour run. The redesign uses bolted ConFlat flanges and a silver-plated copper gasket to seal the vessel under vacuum. I modelled whether the gasket could stay below 450 °C and the fittings and silicone lines below 200 °C.

Thermal model

The 20-body ANSYS model includes the furnace, insulation, melt and electrodes. It accounts for 24 thermal contacts, temperature-dependent material data, latent heat during melting, radiation inside both the furnace and retort, and heat loss to the room.

Reported results and next steps

The calibrated baseline predicted 432 °C at the gasket and 371 °C at the lid, with 702 W at a 981 °C heater setpoint. The portfolio also reports an uncooled gasket result of 410 °C, 40 °C below the design limit, with the fittings and lines below 130 °C. Both reported gasket temperatures are above the 250 °C design target. The portfolio does not identify which conditions changed between the two results.

Next I’ll compare preventative cooling options, run the planned 52-hour transient study, and use the predicted temperatures to check bolt preload.

Exploded ConFlat flange assembly with the gasket highlighted in red
The silver-plated copper gasket sits between the ConFlat flanges.
Photograph and section diagram of the reactor and cooling coil
Reactor hardware and water-cooling layout.

The ANSYS v0 export records the setup and marks its transient solution as unsolved.

All projects

RR27 Track Time Simulation

Formula SAE · MATLAB · Applied Racing Dynamics

MATLAB Applied Racing Dynamics (ARD)
MATLAB plot comparing shift delay and final drive ratio over 75 metres

A new engine and vehicle package changed the RR27’s gearing and acceleration. I used MATLAB and Applied Racing Dynamics to compare final drive ratios and estimate whether 0.05 s pneumatic shifts would be worthwhile compared with 0.50 s mechanical shifts.

Model and results

I collected vehicle data across the team, recreated the Formula SAE Michigan endurance course and a 75 m acceleration course, and checked the MATLAB results in Applied Racing Dynamics.

The updated RR27 study estimated an acceleration event improvement of about 10% with faster shifts. The team selected a 37-tooth rear sprocket and 11-tooth front sprocket (about 3.36:1). A larger rear sprocket would exceed the available space, and 11 teeth was the smallest available front sprocket in the 520 series. The endurance event carries more points, so reliability remains central to the decision on pneumatic shifting.

Map of the endurance course used in the simulation
Formula SAE Michigan endurance course.
Map of the custom acceleration course and braking section
Acceleration course with a 75 m straight and braking section.
Vehicle speed plotted against time across the endurance course
Simulated speed through the endurance course.

The supporting report covers an earlier sweep that favoured a 3.5:1 ratio and estimated smaller gains from faster shifts.

All projects

RR25 Catchcan Mounts

Formula SAE · SOLIDWORKS · PETG

SOLIDWORKS CAD render of the dual catchcan mount

The RR25 needed a lightweight catchcan mount before its final outing at the 2026 Ferrari Fest. I measured the catchcans and frame with calipers, modelled a bracket for both cans in SOLIDWORKS, and 3D printed it in PETG.

White PETG catchcan bracket with two openings
The printed dual catchcan bracket.
All projects

Raspberry Pi Housing & Cooling

SOLIDWORKS · PETG · 3D Printing

Assembled Raspberry Pi enclosure with a vented lid and accessible ports

I designed a vented Raspberry Pi housing in SOLIDWORKS for a smart home server. I printed it in PETG on a Creality Ender 3 V3 SE and selected fans powered by the Raspberry Pi for active cooling.

Open Raspberry Pi case showing its cooling fan and removable vented lid
The enclosure interior and removable lid.

Experience

Raven's Racing (Formula SAE)

Sep 2025 – Present

Simulation, Aerodynamics, Powertrain

I design and analyse drivetrain and powertrain systems for Formula SAE. I redesigned the RR27 drivetrain mount, selected drivetrain components, and prepared drawings for manufacturing. I also run MATLAB and Applied Racing Dynamics studies to evaluate gearing and shift strategies, and use flow bench testing to guide intake design.

Our team placed first at the University of Toronto Shootout in October 2026.

Research Assistant, Carleton University

Sep 2026 – Present

Space Systems R&D

I support research on regenerative lunar bases by modelling and building test hardware for high thermal and pressure loads in vacuum. My FFC reactor work uses thermal modelling to check whether a redesigned vacuum seal can operate at temperature.

Skills

Software

  • SolidWorks
  • Fusion 360
  • MATLAB / Simulink
  • ANSYS
  • SimScale
  • OpenFOAM
  • Python
  • Applied Racing Dynamics
  • Microsoft Office

Engineering

  • 3D CAD & Drafting
  • GD&T
  • FEA
  • CFD
  • Structural Analysis
  • Thermal Analysis
  • Vehicle Simulation
  • Inverse Kinematics & Control
  • 3D Printing
  • Engineering Drawings

Coursework

Thermodynamics, Materials, Solids, Fluids, Mechatronics, Calculus I–III, Mathematical Methods & Simulation

Certification

SOLIDWORKS Design Professional (CSWP) · Awarded November 6, 2026

Keep in touch

Resume and portfolio

A concise overview of my engineering experience, projects and technical skills.

Certificates

Dassault Systèmes · SOLIDWORKS

SOLIDWORKS Design Professional (CSWP)

Issued November 6, 2026 · Credential ID: C-GUEA826DKS

SOLIDWORKS Design Professional certificate awarded to Ahmad Bitar by Dassault Systèmes on November 6, 2026